View B141EW04V7_7868428.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

au optronics corporation b141ew04 v7 product specification document version 0.5 1 ( v ) preliminary specifications ( ) final specifications module 14.1? wxga color tft-lcd model name b141ew04 v7 customer date checked & approved by note: this specification is subject to change witho ut notice. approved by date howard lee 2007/10/9 prepared by mendy wang 2007/10/9 nbbu marketing division / au optronics corporation www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 2 contents 1. handling precautions............................ ................................................... ............................... 4 2. general description............................. ................................................... ................................. 5 2.1 general specification.......................... ................................................... ............................ 5 2.2 optical characteristics ........................ ................................................... ............................ 6 3. functional block diagram ........................ ................................................... ......................... 11 4. absolute maximum ratings........................ ................................................... ....................... 12 4.1 absolute ratings of tft lcd module ............. ................................................... ............. 12 4.2 absolute ratings of backlight unit ............. ................................................... ................... 12 4.3 absolute ratings of environment................ ................................................... .................. 12 5. electrical characteristics ...................... ................................................... ............................. 13 5.1 tft lcd module ................................. ................................................... ......................... 13 5.2 backlight unit................................. ................................................... ............................... 15 6. signal characteristic ........................... ................................................... ............................... 17 6.1 pixel format image............................. ................................................... .......................... 17 6.2 the input data format.......................... ................................................... .......................... 18 6.3 signal description/pin assignment .............. ................................................... ................. 19 6.4 interface timing ............................... ................................................... ............................. 21 7. connector description ........................... ................................................... ............................ 23 7.1 tft lcd module ................................. ................................................... ......................... 23 7.2 backlight unit................................. ................................................... ............................... 23 7.3 signal for lamp connector...................... ................................................... ...................... 23 8. vibration and shock test........................ ................................................... ........................... 24 8.1 vibration test ................................. ................................................... ............................... 24 8.2 shock test spec: ............................... ................................................... ........................... 24 9. reliability..................................... ................................................... ........................................ 25 10. mechanical characteristics ..................... ................................................... ........................ 26 10.1 lcm outline dimension......................... ................................................... ..................... 26 11. shipping and package ........................... ................................................... .......................... 29 11.1 shipping label format......................... ................................................... ....................... 29 11.2. carton package............................... ................................................... ........................... 30 11.3 shipping package of palletizing............... ................................................... .................... 31 12. appendix: edid description ..................... ................................................... ....................... 32 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 3 record of revision version and date page old description new description remark 0.1 2007/07/16 all first edition for customer 0.2 2007/9/17 5 luminance uniformity: 1.3 max (5 points) luminance uniformity: 1.25 max (5 points) 5 power consumption: 5.2 typ power consumption: 5. 1 typ 6 wx: 0.280 min, 0.313 typ, 0.343 max wx: 0.285 min, 0.313 typ, 0.341 max 6 wy: 0.299min, 0.329 typ, 0.359 max wy: 0.309 min, 0.329 typ, 0.349 max 12 absolute ratings of backlight unit: 3.0 min absolute ratings of backlight unit: 2.0 min 15 ccfl current(iccfl): 3.0 min ccfl current(iccfl ): 2.0 min 15 ccfl frequency(fccfl): 50 min, 55 typ, 60 max ccfl frequency(fccfl): 50 min, 60 typ, 80 max 15 ccfl power consumption(pccfl): 4.3 typ ccfl power consumption(pccfl): 4.1 typ 22 power sequence time t1: 0.5 min power sequence time t1: 0.3 min 22 power sequence time t3: 50 max power sequence time t3: - max 22 power sequence time t4: 400 min power sequence time t4: 150 min 22 power sequence time t6: 200 min power sequence time t6: 0 min 0.3 2007/9/26 6 viewing angle: 40/40/10/30 min. vie wing angle: 40/40/15/30 min. 6 viewing angle: 45/45/20/35 typ. viewing angle: 4 5/45/20/40 typ. 6 luminance uniformity(5 point): 1.30 max luminance uniformity(5 point): 1.25 max 0.4 2007/10/1 29 11s42t0338z1zdt1c00000 707 p/n 42t0338 fru 42t0339 30 customer no: customer no: p/n 42t0338 0.5 2007/10/9 26 lcm outline dimension 27 lcm outline dimension www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 4 1. handling precautions 1) since front polarizer is easily damaged, pay att ention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact wi th water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with a bsorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break o r crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) in case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the ccfl reflector edge. instead, press at the far ends of the cfl ref lector edge softly. otherwise the tft module may be damaged. 10) at the insertion or removal of the signal inter face connector, be sure not to rotate nor tilt the interface connector of the tft module. 11) after installation of the tft module into an en closure (notebook pc bezel, for example), do not twist nor bend the tft module even momentary. at designing the enclosure, it should be taken into consideration th at no bending/twisting forces are applied to the tft module from outside. otherwise the tft module may be damaged. 12) cold cathode fluorescent lamp in lcd contains a small amount of mercury. please follow local ordinances or regulations for disposal. 13) small amount of materials having no flammabilit y grade is used in the lcd module. the lcd module should be supplied by power complied wit h requirements of limited power source(, iec60950 or ul1950), or be applied exempti on. 14) the lcd module is designed so that the ccfl in it is supplied by limited current circuit(iec60950 or ul1950). do not connect the ccf l in hazardous voltage circuit. www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 5 2. general description b141ew04 v7 is a color active matrix liquid crystal display composed of a tft lcd panel, a driver circuit, and backlight system. the screen format is intended to support the wxga (1280(h) x 800(v)) screen and 262k colors (rgb 6-bi ts data driver). all input signals are lvds interface compatible. inverter of backlight is not included. b141ew04 v7 is designed for a display unit of noteb ook style personal computer and industrial machine. 2.1 general specification the following items are characteristics summary on the table at 25 condition: items unit specifications screen diagonal [mm] 357.7 (14.1 w?) active area [mm] 303.36(h) x 189.6 (v) pixels h x v 1280x3(rgb) x 800 pixel pitch [mm] 0.237 pixel arrangement r.g.b. vertical stripe display mode normally white white luminance (iccfl=6.0ma) note: iccfl is lamp current [cd/m 2 ] 200 typ. (5 points average) 170 min. (5 points average) ( note1 ) luminance uniformity 1.25 max. (5 points) contrast ratio 400:1 typ.,300:1 min. optical rise time/fall time [msec] 16 typ., 25 max. nominal input voltage vdd [volt] +3.3 typ. power consumption [watt] 5.1 typ weight [grams] 400 g typ., 420g max. physical size [mm] 320 max. (w) x 206 max. (h) x 5 .5 max.(t). electrical interface r/g/b data, 3 sync, signals, clock (4 pairs lvds) surface treatment hard coating 3h, anti-reflection type support color 262k colors ( rgb 6-bit ) temperature range operating storage (non-operating) [ o c] [ o c] 0 to +50 -20 to +60 rohs compliance rohs compliance www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 6 2.2 optical characteristics the optical characteristics are measured under stab le conditions at 25 (room temperature) : item unit conditions min. typ. max. note white luminance i ccfl =6.0ma [cd/m 2 ] 5 points average 170 200 - 1, 4, 5. [degree] [degree] horizontal (right) cr = 10 (left) 40 40 45 45 - - viewing angle [degree] [degree] vertical (upper) cr = 10 (lower) 15 30 20 40 - - 9 luminance uniformity 5 points 1.25 1 luminance uniformity 13 points 1.53 2 cr: contrast ratio 300 400 - 6 cross talk % 1.4 7 [msec] rising - 5 8 [msec] falling - 11 17 response time [msec] rising + falling 16 25 8 red x 0.545 0.575 0.605 red y 0.305 0.335 0.365 green x 0.285 0.315 0.345 green y 0.520 0.550 0.580 blue x 0.125 0.155 0.185 blue y 0.105 0.135 0.165 white x 0.285 0.313 0.341 color / chromaticity coordinates (cie 1931) white y 0.309 0.329 0.349 note 1: 5 points position (display area : 303.7 (h) x 189.8(v)mm) www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 7 1 2 3 4 5 h /4 h /4 h /4 h /4 h w w /4 w /4 w /4 w /4 note 2: 13 points position w /4 w w /4 h h /4 h /4 h /4 h /4 7 9 1 0 w /4 1 8 w /4 1 0 1 0 1 0 1 0 2 3 1 3 1 2 4 5 6 1 1 note 3: the luminance uniformity of 5 and 13 point s is defined by dividing the maximum luminance valu es by the minimum test point luminance w13 = maximum brightness of thirteen points minimum brightness of thirteen points maximum brightness of five point s w5 = minimum brightness of five points www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 8 note 4: measurement method the lcd module should be stabilized at given temper ature for 30 minutes to avoid abrupt temperature ch ange during measuring. in order to stabilize the luminan ce, the measurement should be executed after lighti ng backlight for 30 minutes in a stable, windless and dark room. note 5 definition of average luminance of white (y l ): measure the luminance of gray level 63 at 5 points y l = [l (1)+ l (2)+ l (3)+ l (4)+ l (5)] / 5 l (x) is corresponding to the luminance of the poin t x at figure in note (1). note 6 definition of contrast ratio: contrast ratio is calculated with the following for mula. center of the screen tft - lcd module 50 cm photo detector lcd panel field=2 contrast ratio (cr)= brightness on the ?white? state brightness on the ?black? state www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 9 note 7 definition of cross talk (ct) ct = | y b ? y a | / y a 100 (%) where y a = luminance of measured location without gray level 0 pattern (cd/m 2 ) y b = luminance of measured location with gray level 0 pattern (cd/m 2 ) note 8: definition of response time: the output signals of bm-7 or equivalent are measur ed when the input signals are changed from ?black? to ?white? (falling time) and from ?white? to ?black? (rising time), respectively. the response time inte rval between the 10% and 90% of amplitudes. refer to figure as b elow. "black" tr tf "white" "white" 0 % 10 % 90 % 100 % optical response www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 10 note 9. definition of viewing angle viewing angle is the measurement of contrast ratio 10, at the screen center, over a 180 horizontal an d R 180 vertical range (off-normal viewing angles). th e 180 viewing angle range is broken down as follow s; 90 ( ) horizontal left and right and 90 ( ) vertical, high (up) and low (down). the measureme nt direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle. www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 11 3. functional block diagram the following diagram shows the functional block of the 14. 1inches wide color tft/lcd module: tft array/cell vdd lcd controller lcd drive card backlight unit 1280(r/g/b) x 3 gnd dc-dc converter ref circuit y-driver x-driver rxin0 rxin1 rxin2 rxclkin (4 pairs lvds) jae fi-xb30sl-hf10 mating contactfi-xc3-1-15000 mating housing jae fi-x30sl jst bhsr-02vs-1 mating type sm02b-bhss-1- tb lamp connector(2pin) www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 12 4. absolute maximum ratings absolute maximum ratings of the module is as follow ing: 4.1 absolute ratings of tft lcd module item symbol min max unit conditions logic/lcd drive voltage vdd -0.3 +4.0 [volt] note 1,2 4.2 absolute ratings of backlight unit item symbol min max unit conditions ccfl current icfl 2.0 6.5 [ma] rms note 1,2 4.3 absolute ratings of environment item symbol min max unit conditions operating temperature top 0 +50 [ o c] note 3 operation humidity hop 5 95 [%rh] note 3 storage temperature tst -20 +60 [ o c] note 3 storage humidity hst 5 95 [%rh] note 3 note 1: at ta (25 ) note 2: permanent damage to the device may occur if exceed maximum values note 3: for quality performance, please refer to au o iis(incoming inspection standard). twb=39c operating range storage range www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 13 5. electrical characteristics 5.1 tft lcd module 5.1.1 power specification input power specifications are as follows; symble parameter min typ max units note vdd logic/lcd drive voltage 3.0 3.3 3.6 [volt] pdd vdd power 1.0. [watt] note 1 idd idd current 303 [ma] note 1 i rush inrush current 810 1500 [ma] note 2 vddrp allowable logic/lcd drive ripple voltage 100 [mv] p-p note 1 : maximum measurement condition black patterm note 2 measure condition q3 ao6402 g d2 s d1 d5 d6 c3 0.01uf/25v c2 1uf/25v c1 1uf/16v q3 ao6402 g d2 s d1 d5 d6 f1 vr1 47k +12.0v vcc sw1 sw mag-spst 1 2 (lcd module input) (high to low) control signal r2 1k r2 1k r1 47k +3.3v 90% 10% vin rising time 0v 3.3v 0.5ms www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 14 5.1.2 signal electrical characteristics input signals shall be low or high-impedance state when vdd is off. signal electrical characteristics are as follows; parameter condition min max unit vth differential input high threshold (vcm=+1.2v) 100 [mv] vtl differential input low threshold (vcm=+1.2v) -100 [mv] vcm differential input common mode voltage 1.125 1.375 [v] note: lvds differential voltage www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 15 5.2 backlight unit parameter guideline for ccfl inverter parameter min typ max units condition white luminance 5 points average 170 200 - [cd/m 2 ] (ta=25 ) ccfl current(iccfl) 2.0 6.0 6.5 [ma] rms (ta=25 ) note 2 ccfl frequency(fccfl) 50 60 80 [khz] (ta=25 ) note 3,4 ccfl ignition voltage(vs) 1500 [volt] rms (ta= 0 ) note 5 ccfl ignition voltage(vs) 1060 [volt] rms (ta= 25 ) note 5 ccfl voltage (reference) (vccfl) 630 655 845 [volt] rms (ta=25 ) note 6 ccfl power consumption (pccfl) - 4.1 4.6 [watt] (ta=25 ) note 6 note 1: typ are auo recommended design points. *1 all of characteristics listed are measured under the condition using the auo test inverter. *2 in case of using an inverter other than listed, it is recommended to check the inverter carefully. sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker at low power may happen. *3 in designing an inverter, it is suggested to che ck safety circuit very carefully. impedance of ccfl , for instance, becomes more than 1 [m ohm] when cfl is d amaged. *4 generally, ccfl has some amount of delay time af ter applying kick-off voltage. it is recommended to keep on applying kick-off voltage for 1 [sec] until discharge. *5 ccfl discharge frequency must be carefully chose n so as not to produce interfering noise stripes on the screen. *6 reducing ccfl current increases ccfl discharge v oltage and generally increases ccfl discharge frequency. so all the parameters of an inverter sho uld be carefully designed so as not to produce too much leakage current from high-voltage output of the inv erter. note 2: it should be employed the inverter which ha s ?duty dimming?, if iccfl is less than 4ma. note 3: ccfl discharge frequency should be carefull y determined to avoid interference between inverter and tft lcd. note 4: the frequency range will not affect to lamp life and reliability characteristics. www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 16 note 5: ccfl inverter should be able to give out a power that has a generating capacity of over 1,430 voltage. lamp units need 1,400 voltage minimum for ignition. note 6: calculator value for reference (i ccfl v ccfl =p ccfl ) note 7: requirements for a system inverter design, which is intended to have a better display performa nce, a better power efficiency and a more reliable lamp, a re following. it shall help increase the lamp lifetime and reduce leakage current. a. the asymmetry rate of the inverter waveform shou ld be less than 10%. b. the distortion rate of the waveform should bewit hin 2 10%. * inverter output waveform had better be more simil ar to ideal sine wave. www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 17 6. signal characteristic 6.1 pixel format image following figure shows the relationship of the inpu t signals and lcd pixel format. r g b r g b r g b r g b r g b r g b r g b r g b 0 1 1278 1279 1st line 800th line www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 18 6.2 the input data format signal name description +r5 +r4 +r3 +r2 +r1 +r0 red data 5 (msb) red data 4 red data 3 red data 2 red data 1 red data 0 (lsb) red-pixel data red-pixel data each red pixel's brightness data consists of these 6 bits pixel data. +g5 +g4 +g3 +g2 +g1 +g0 green data 5 (msb) green data 4 green data 3 green data 2 green data 1 green data 0 (lsb) green-pixel data green-pixel data each green pixel's brightness data consists of these 6 bits pixel data. +b5 +b4 +b3 +b2 +b1 +b0 blue data 5 (msb) blue data 4 blue data 3 blue data 2 blue data 1 blue data 0 (lsb) blue-pixel data blue-pixel data each blue pixel's brightness data consists of these 6 bits pixel data. rxclkin data clock the typical frequency is 68.94 mhz.. the signal is used to strobe the pixel data and de signals. all pixel data shall be valid at the falling edge when the de signal is high. de display timing this signal is strobed at the fal ling edge of rxclkin. when the signal is high, the pixel data shall be valid to be displayed. vs vertical sync the signal is synchronized to rxcl kin . hs horizontal sync the signal is synchronized to rx clkin . note: output signals from any system shall be low o r high-impedance state when vdd is off. www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 19 6.3 signal description/pin assignment lvds is a differential signal technology for lcd in terface and high speed data transfer device. pin# signal name pin# signal name 1 gnd 2 vdd 3 vdd 4 v edid 5 aging 6 clk edid 7 data edid 8 rxin0- 9 rxin0+ 10 gnd 11 rxin1- 12 rxin1+ 13 gnd 14 rxin2- 15 rxin2+ 16 gnd 17 rxclkin- 18 rxclkin+ 19 gnd 20 nc 21 nc 22 gnd 23 nc 24 nc 25 gnd 26 nc 27 nc 28 gnd 29 nc 30 nc www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 20 note1: start from right side note2: input signals shall be low or high-impedance state when vdd is off. internal circuit of lvds inputs are as following. the module uses a 100ohm resistor between positive and negative data lines of each receiver input r r r r lvds receiver signal input pin no. 9 11 12 14 15 17 18 8 rxin0+ rxin0- rxin1+ rxin1- rxin2+ rxin2- rxclkin+ rxclkin- www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 21 6.4 interface timing 6.4.1 timing characteristics basically, interface timings should match the 1280x 800 /60hz manufacturing guide line timing. parameter symbol min. typ. max. unit frame rate - 50 60 - hz clock frequency 1/ t clock 69.25 mhz period t v 803 822 1023 active t vd 800 800 800 vertical section blanking t vb 3 22 223 t line period t h 1303 1404 2047 active t hd 1280 1280 1280 horizontal section blanking t hb 23 124 767 t clock note : de mode only 6.4.2 timing diagram dotclk de t h t hb t hd de t v t vb t vd input timing definition ( de mode) t clock input data pixel 1 pixel 2 pixel 3 pixel n-1 pixel n invaild data invaild data pixel 1 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 22 6.5 power on/off sequence vdd power and lamp on/off sequence is as follows. i nterface signals are also shown in the chart. signals from any system shall be hi-z state or low level when vdd is off. power sequence timing value parameter min. typ. max. units t1 0.3 - 10 (ms) t2 0 - 50 (ms) t3 0 - - (ms) t4 150 - - (ms) t5 200 - - (ms) t6 0 - - (ms) t7 0 - 10 (ms) t4 t3 t2 t5 valid data t1 10% 90% 10% 90% t6 t 7 power supply vdd lvds interface backlight on www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 23 7. connector description physical interface is described as for the connecto r on module. these connectors are capable of accommodating the f ollowing signals and will be following components. 7.1 tft lcd module connector name / designation for signal connector manufacturer jae type / part number fi-xb30sl-hf10 mating housing/part number f1-x30h mating contact/part number f1-xc3-1-15000 7.2 backlight unit physical interface is described as for the connecto r on module. these connectors are capable of accommodating the f ollowing signals and will be following components. connector name / designation for lamp connector manufacturer jst type / part number bhsr-02vs-1 mating type / part number sm02b-bhss-1-tb 7.3 signal for lamp connector pin # cable color signal name 1 red lamp high voltage 2 white lamp low voltage www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 24 8. vibration and shock test 8.1 vibration test test spec: test method: non-operation acceleration: 1.5g frequency: 10 - 500hz sweep: half sine wave 60mins/axis 8.2 shock test spec: test spec: test method: non-operation acceleration: 240 g , half sine wave active time: 2 ms pulse: half sine wave www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 25 9. reliability items required condition note temperature humidity bias 50 / 80,1000hr high temperature operation 50 /20%,300hr low temperature operation 0 ,500hr on/off test 25 , on/30 sec. off/30sec., 30,000 cycles, 500 hours hot storage 60 /20% rh ,300 hours cold storage -20 /20% rh ,300 hours thermal shock test (-25 to +65 ) ramp 25 /min duration at temp=60min shock test (non-operating) 240g,2ms for half sine pulse, 1 time for x, y, z 6 directions vibration test (non-operating) 1.5g, 10~500hz/half sine wave,60mins/axis esd contact : 8kv, operation, class b air : 15kv, operation, class b note 1 note1: according to en61000-4-2 , esd class b: some performance degradation allowed. no data lost . self-recoverable. no hardware failures. note2: ccfl life time: 12,000 hours minimum und er normal module usage. note3: mtbf (excluding the ccfl): 30,000 hours with a confidence level 90% www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 26 10. mechanical characteristics 10.1 lcm outline dimension www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 27 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 28 10.2 screw hole depth and center position screw hole maximum depth, from side surface =2.5 mm (see drawing) screw hole center location, from front surface = 3. 1 0.3mm (see drawing) screw torque: maximum2.5 kgf-cm www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 29 11. shipping and package 11.1 shipping label format h/w source ic gate ic 0a raydium nt 0a 0axxg b141ew04 v7 11s 42t0338 z 1zdt1c00000 707 p/n 42t0338 fru 42t0339 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 30 11.2. carton package carton label: 80mm * 40mm the outside dimension of carton is 454(l)mm* 388(w) mm* 352(h)mm, carton and cushion weight are 2920g. 97.14b28.700 b141ew04 v7 p/n 42t0338 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 31 11.3 shipping package of palletizing by air : 6 *4 layers, one pallet put 24 boxes, tota l 480 pcs module. by sea : 6 *5 layers, one pallet put 30 boxes, tota l 600 pcs module. bottom cardboard top cardboard stretch film corner angle wooden pallet pet band label www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 32 12. appendix: edid description byte# byte# data data data (decimal) (hex) field name and comments (decimal) (hex) (bin) 0 00 header 0 00 00000000 1 01 header 255 ff 11111111 2 02 header 255 ff 11111111 3 03 header 255 ff 11111111 4 04 header 255 ff 11111111 5 05 header 255 ff 11111111 6 06 header 255 ff 11111111 7 07 header 0 00 00000000 8 08 id system manufacturer name 48 30 00110000 9 09 compressed ascii 174 ae 10101110 10 0a id product code (lsb) 49 31 00110001 11 0b id product code (msb) 64 40 01000000 12 0c lcd module serial no. 0 00 00000000 13 0d lcd module serial no. 0 00 00000000 14 0e lcd module serial no. 0 00 00000000 15 0f lcd module serial no. 0 00 00000000 16 10 week of manufacture 1 01 00000001 17 11 year of manufacture 16 10 00010000 18 12 edid structure version 1 01 00000001 19 13 edid revision 3 03 00000011 20 14 video input definition 128 80 10000000 21 15 max h image size( M ) 30 1e 00011110 22 16 max v image size( M ) 19 13 00010011 23 17 display gamma 120 78 01111000 24 18 feature support(dpms) 234 ea 11101010 25 19 red/green low bits 135 87 10000111 26 1a blue/white low bits 197 c5 11000101 27 1b red x 148 94 10010100 28 1c red y 87 57 01010111 29 1d green x 79 4f 01001111 30 1e green y 140 8c 10001100 31 1f blue x 39 27 00100111 32 20 blue y 37 25 00100101 33 21 white x 80 50 01010000 34 22 white y 84 54 01010100 35 23 established timing i 0 00 00000000 36 24 established timing ii 0 00 00000000 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 33 37 25 manufacturer's timings 0 00 00000000 38 26 standard timing identification 1 1 01 00000001 39 27 standard timing identification 1 1 01 00000001 40 28 standard timing identification 2 1 01 00000001 41 29 standard timing identification 2 1 01 00000001 42 2a standard timing identification 3 1 01 00000001 43 2b standard timing identification 3 1 01 00000001 44 2c standard timing identification 4 1 01 00000001 45 2d standard timing identification 4 1 01 00000001 46 2e standard timing identification 5 1 01 00000001 47 2f standard timing identification 5 1 01 00000001 48 30 standard timing identification 6 1 01 00000001 49 31 standard timing identification 6 1 01 00000001 50 32 standard timing identification 7 1 01 00000001 51 33 standard timing identification 7 was not used 1 01 00000001 52 34 standard timing identification 8 was not used 1 01 00000001 53 35 standard timing identification 8 was not used 1 01 00000001 54 36 pixel clock/10,000 (lsb) 13 0d 00001101 55 37 pixel clock/10,000 (msb) / 27 1b 00011011 56 38 horizontal active 0 00 00000000 57 39 horizontal blanking 124 7c 01111100 58 3a horizontal active : horizontal blanking 80 50 01010000 59 3b vertical active 32 20 00100000 60 3c vertical blanking 22 16 00010110 61 3d vertical active : vertical blanking 48 30 00110000 62 3e horizontal sync. offset 48 30 00110000 63 3f horizontal sync pulse width 32 20 00100000 64 40 vertical sync offset : sync width 54 36 00110110 65 41 horizontal vertical sync offset/width upper 2bits 0 00 00000000 66 42 horizontal image size 48 30 00101111 67 43 vertical image size 190 be 10111110 68 44 horizontal & vertical image size (upper 4bit) 16 10 00010000 69 45 horizontal border = 0 0 00 00000000 70 46 vertical border = 0 0 00 00000000 71 47 non-interlaced, normal display, no stereo, digital separate sync ,h/v pol negatives 24 18 00011000 72 48 pixel clock/10,000 (lsb) 50hz 139 8b 10001011 73 49 pixel clock/10,000 (msb) / 50hz 22 16 00010110 74 4a horizontal active 0 00 00000000 75 4b horizontal blanking 124 7c 01111100 76 4c horizontal active : horizontal blanking 80 50 01010000 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 34 77 4d vertical active 32 20 00100000 78 4e vertical blanking 22 16 00010110 79 4f vertical active : vertical blanking 48 30 00110000 80 50 horizontal sync. offset 48 30 00110000 81 51 horizontal sync pulse width 32 20 00100000 82 52 vertical sync offset : sync width 54 36 00110110 83 53 horizontal vertical sync offset/width upper 2bits 0 00 00000000 84 54 horizontal image size 48 30 00101111 85 55 vertical image size 190 be 10111110 86 56 horizontal & vertical image size (upper 4bit) 16 10 00010000 87 57 horizontal border = 0 0 00 00000000 88 58 vertical border = 0 0 00 00000000 89 59 non-interlaced, normal display, no stereo, digital separate sync, h/v pol negatives 24 18 00011000 90 5a detailed timing descriptor #3 0 00 00000000 91 5b 0 00 00000000 92 5c 0 00 00000000 93 5d 15 0f 00001111 94 5e 0 00 00000000 95 5f (horizontal active pixel /8)-31 129 81 10000001 96 60 image aspect ratio(15:9) 10 0a 00001010 97 61 low refresh rate #1(50hz) 50 32 00110010 98 62 (horizontal active pixel /8)-31 129 81 10000001 99 63 image aspect ratio(16:10) 10 0a 00001010 100 64 low refresh rate #2(40hz) 40 28 00101000 101 65 brightness(1/10nit) 18 12 00010010 102 66 feature flag(tn mode) 1 01 00000001 103 67 reserved 00h 0 00 00000000 104 68 eisa manufacturer code(3 character id) 6 06 00000110 105 69 compressed ascii 175 af 10101111 106 6a panel supplier reserved - product code 68 44 01000100 107 6b (hex, lsb first) 71 47 00100100 108 6c detailed timing descriptor #4 0 00 00000000 109 6d 0 00 00000000 110 6e 0 00 00000000 111 6f 254 fe 11111110 112 70 0 00 00000000 113 71 (supplier s/n) 66 42 01000010 114 72 (supplier s/n) 49 31 00110001 115 73 (supplier s/n) 52 34 00110100 116 74 (supplier s/n) 49 31 00110001 www.datasheet.co.kr datasheet pdf - http://www..net/
au optronics corporation b141ew04 v7 product specification document version 0.5 35 117 75 (supplier s/n) 69 45 01000101 118 76 (supplier s/n) 87 57 01010111 119 77 (supplier s/n) 48 30 00110000 120 78 (supplier s/n) 52 34 00110010 121 79 (supplier s/n) 32 20 00100000 122 7a (supplier s/n) 86 56 01010110 123 7b (supplier s/n) 55 37 00110100 124 7c (supplier s/n) 32 20 00100000 125 7d (supplier s/n) 10 0a 00001010 126 7e extension flag = 00 0 00 00000000 127 7f checksum 153 99 11000001 www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of B141EW04V7

	To Download B141EW04V7 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .